trainng

1. INSTALASI PENERANGAN

    480 Jam Latihan    : PPKPI Ps. Rebo

    320 Jam Latihan    : BLKD Utara

2. INSTALASI TENAGA

480 Jam Latihan    : PPKPI Ps. Rebo

320 Jam Latihan    : BLKD Utara

3. INSTALASI KONTROL MOTOR

80 Jam Latihan        : PPKPI Ps. Rebo

35 Jam Latihan     : MSI. Training Consultant

 4. MAINTENANCE LISTRIK

80Jam Latihan        : PPKPI Ps. Rebo

35 Jam Latihan       : MSI. Training Consultant

5. KELISTRIKAN KAPAL : MSI. Training Konsultant
35 Jam Latihan       : MSI. Training Consultant

6. PROGRAMMABLE LOGIC CONTROL ( PLC )

35 JAM LATIHAN      : MSI. TRAINING CONSULTANT

7. AC/REFR. MAINTENANCE

35 JAM LATIHAN          : MSI. TRAINING CONSULTANT

8. REWINDING 3 PHASE MOTOR

35 JAM LATIHAN             : MSI. TRAINING CONSULTANT

 

MSI. TRAINING CONSULTANT

Jl. Plumpang Semper, Kp. Walang, Rt.10/03, No. 15, Kel. Rawa Badak Selatan, Jakarta Utara.

E-Mail : msi.trainingconsultant@yahoo.com/syeh_habas@yahoo.com

Phone : 081231905535/082260317057

————————————————————————————————————————————-

 

TRAINING PROGRAMME

 

1. Name of Training : “ELECTRIC MAINTENANCE”/”KELISTRIKAN KAPAL”

 

2. Duration              :  5 Days ( @ 7 hrs )

 

3. Cost of Course     : Rp. 3.500.000,-/Candidat 

 

4. Goal                    :

After finished this Training Candidat should be able to :

a. Explain about Basic Electriciy, like Ohms Law, Electric Power, Series and

Parallel  Connection

b. Use Electric Measuremen tools, like Multy Meter (A/D), Clip On Meter,

Insulation Tester.

c. Explain  Schema Diagrame of Brushless Generator; Star Delta Connection;

Content of Electric Motor Name Plate; Impedance, Voltage and Current in

Star and Delta Connection.

d. Reading and Installing Motor Control. like Direct On Line Connection;

Forward and Reverse Connection; Star Delta Starter Motor.

 

5. Curriculum :

a. Basic Electricity                    7 hrs.

b. Electric Measurement         : 7 hrs.(T/P)

c. Generator and Motor         :  7  hrs.

d. Electric Motor Control     : 24  hrs (T/P)

 

6. Syllabus :

a. Basic Electricity

– Understanding of Voltage; Current and Resistance

– Resistance Value in Some Material

– Ohms Law

– Electric Power 1 phase and 3 phase

– Series and Parallel Connection

b. Electric Measurement

– Volt Meter

– Amps. Meter

– Ohms Meter

– Multy Meter

– Clip On Meter

– Insulation Meter ( Megger )

c. Generator and Motor

– Electromagnet

– Generator and Electric Motor

– Carbon Brush and Brushless Generator

– 3 phase Motor ( Squirrel Gauge )

– Star Delta Connection

– Forward and Reverse 3 phase Electric Motors

 

d. Electric Motor Control ( Reading Wiring Diagram )

– Component of Motor Control ( Symbol and Spec )

– Basic Wiring Diagrame of Control Motor

– D.O.L; Control Motor from more then 2 position; Forward and Reverse; Star Delta Starter Motor Control

 

7. Facilities

a.  Hand Out

b. Certificate

 

Jakarta, 13 SEPTEMBER 2014

Drs.Hasan Basri,CH,CHt.

Principal

————————————————————–

MSI. TRAINING CONSULTANT

Jl. Plumpang Semper, Kp. Walang, Rt.10/03, No. 15, Kel. Rawa Badak Selatan, Jakarta Utara.

E-Mail : msi.trainingconsultant@yahoo.com/syeh_habas@yahoo.com

Phone : 081231905535/082260317057

————————————————————————————————————————————-

TRAINING PROGRAMME

 

1. Name of Training : “PROGRAMMABLE LOGIC CONTROL (PLC)”

2. Duration                     :  5 Days (@ 7 hrs)

3. Cost                            : Cost of Course Rp.5.000.000,-/Candidat                                   

4. Goal                           :

  After finished this Training Candidat should be able to :

  • · Explain Configuration of PLC. (Programmable Logic Control)
  • Install Input/Out put Component and pheriperial PLC.
  • Arrange Input/Output Assignment.
  • Arrange Ladder Diagram Control
  • Arrange Mnemonic (Programme Logic)

 

5. Kurikulum/Syllabus  (35 Hrs)

Pemasangan Instalasi PLC

  • Pengawatan dan konfigurasi PLC.
  • Pemasangan Unit CPU, I/O  dan Unit – unit penunjang PLC
  • Pemasangan Komponen I/O  (tombol tekan / Push Button, sakelar, sensor, relay, motor dll)
  • Pemasangan kabel Power Suply dan  Komponen I/O dengan Modul Relay I/O
  • Pengecekan sambungan  modul Relay I/O PLC

Pengoperasian PLC

  • Pengawatan dan konfigurasi PLC
  • Pemasangan Unit Pemrograman (komputer atau programming console)
  • Setting awal  PLC.
  • laddder Diagram  
  • Mnemonic
  • Operasional PLC tiap-tiap Program

 

6. REWINDING MOTOR

    80 Jam Latihan        : PPKPI Ps. Rebo

    40 Jam Latihan        : MSI. Training Consultant

 

7. TEKNIK PENDINGIN

Jakarta, 13 September 2014

Drs.Hasan Basri,CH,CHt.

Principa

MSI. TRAINING CONSULTANT

Jl. Plumpang Semper, Kp. Walang, Rt.10/03, No. 15, Kel. Rawa Badak Selatan, Jakarta Utara.

E-Mail : msi.trainingconsultant@yahoo.com/syeh_habas@yahoo.com

Phone : 081231905535/082260317057

————————————————————————————————————————————- 

TRAINING PROGRAMME

 

1. Name of Training : “REFRIGERATOR & AIR  CONDITION MAINTENANCE”

 

2. Duration              :  5 Days ( @ 7 hrs )

 

3. Cost                    :   Rp. 5000.000,-/candidat

                                 

4. Goal                    :

After finished this Training Candidat should be able to :

a. Explain about Basic  Refrigeration and Air Conditioning

b. Know and understand name and function of Refr. And AC. Component

c. Explain  Schema Diagrame of conrrol System of Refr. And AC. System

d. Axplain about Air Handling System

e. Handle/Shoot kind of Trouble in Refr. And AC system

5. Curriculum :

1. Basic Refrigeration And Air Condition

2. Refrigeration And Air Conditioning Component

3. Control System

4. Air Handling System

5. Trouble Shooting

 

6. Syllabus :

1. Basic Refrigeration And Air Condition

–  Basic of Circulation  ofRefrigerant

– Basic Electricity Control

2. Refrigeration And Air Conditioning Component

– Kind Of Refr. And AC Component

( Compressor; Blower; Condensor; Evaporator; Thermostat; Over Load Relay;

Capasitor; Heater; Filter etc. )

3. Control System

– Reading and Installing of Wiring Diagram Control

4. Air Handling System

– Calculate Capacity of Machine for Air Handling

5. Trouble Shooting

– Trouble shooting for Refrigerant circulation

– Trouble Shooting for Control System

 

7. Facilities

a.  Hand Out

b. Certificate

 

 

Jakarta, 13 September 2014

Drs.Hasan Basri,CH,CHt.

Principal

    80 Jam Latihan        : PPKPI Ps. Rebo

  40 Jam Latihan        : MSI. Training Consultant

 

[wc_row][wc_column size=”one-half” position=”first”]

IMG0323A

TRAINING PLC

[/wc_column][wc_column size=”one-half” position=”last”]

DIVANANDA-&-M-resize

[/wc_column][/wc_row]

[wc_row][wc_column size=”one-half” position=”first”]

2014514053002-(resize)

TRAINING BATTREY AND BATTREY CHARGER

[/wc_column][wc_column size=”one-half” position=”last”]

Kolyubi n Randy maulana

TRAINING REWINDING  3 PHASE MOTOR

[/wc_column][/wc_row]

[wc_row][wc_column size=”one-half” position=”first”]

2014516140421-resize

PRAKTEK KONTROL MOTOR ( TRAINING ELECTRIC MAINTENANCE )

[/wc_column][wc_column size=”one-half” position=”last”]

 

[/wc_column][/wc_row]

Leave a Reply

Your email address will not be published. Required fields are marked *