A. Hard Skill Training

1. Electrical Technique  ( Training Kelistrikan )
a. Kelistrikan Kapal / Electric Maintenanc
b. PLC. ( Programmable Logic Control )

c. Rewinding Electro Motor
d. Safety / Electrcical Safety

2. Refrigeration
Air Condition and Refrigeration Maintenance

 

3. Welding
a. Acethylen
b. Arc Welding

B. Soft Skill Training

1. Motivation with NLP
2. Character Building with NLP
3. Communication Skill with NLP
4. Hypno Teaching/NLP for Teacher
5. Hypno Parenting
6. Customer Service Excellence with NLP.
7. Kewirausahaan dan AMT

1. ELECTRIC MAINTENANCE TRAINING PROGRAMME
1. Name of Training : “ELECTRIC MAINTENANCE”
2. Duration: 5 Days ( @ 6 hrs )
3. Cost : – Cost of Course : Rp. 4.000.000,-/Candidat
4. Goal :

After finished this Training Candidat should be able to :

a. Explain about Basic Electricity, like Ohms Law, Electric Power, Series and Parallel Connection
b. Use Electric Measuremen tools, like Multy Meter (A/D), Clip On Meter, Insulation Tester.
c. Explain Schema Diagrame of Brushless Generator; Star Delta Connection; Content of Electric Motor Name Plate; Impedance, Voltage and Current in Star and Delta Connection.
d. Reading and Installing Motor Control. like Direct On Line Connection; Forward and Reverse Connection; Star Delta Starter Motor.
5. Curriculum :
a. Basic Electricity              ; 6 hrs.
b. Electric Measurement   : 6 hrs.(T/P)
c. Generator and Motor    : 6 hrs.
d. Electric Motor Control :  12 hrs (T/P)
6. Syllabus :
a. Basic Electricity
– Understanding of Voltage; Current and Resistance
– Resistance Value in Some Material
– Ohms Law
– Electric Power 1 phase and 3 phase
– Series and Parallel Connection
b. Electric Measurement
– Volt Meter
– Amps. Meter
– Ohms Meter
– Multy Meter
– Clip On Meter
– Insulation Meter ( Megger )
c. Generator and Motor
– Electromagnet
– Generator and Electric Motor
– Carbon Brush and Brushless Generator
– 3 phase Motor ( Squirrel Gauge )
– Star Delta Connection
– Forward and Reverse 3 phase Electric Motors

d. Electric Motor Control ( Reading Wiring Diagram )
– Component of Motor Control ( Symbol and Spec )
– Basic Wiring Diagrame of Control Motor
– D.O.L; Control Motor from more then 2 position; Forward and Reverse; Star Delta Starter Motor Control

7. Facilities
a. Hand Out
b. Certific

 

2. PROGRAMMABLE LOGIC CONTROLE ( PLC )
     TRAINING PROGRAMME
1. Name of Training : PROGRAMMABLE LOGIC CONTROL (PLC).
2. Duration : 5 Days ( @ 7 hrs ).
3. Cost : – Cost of Course : Rp. 5.500.000,- /Candidat ( In Hause)
Rp. 5.000.000,-/Candidat ( Institutional )

4. Goal :
After finished this Training Candidat should be able to :
• Explain Configuration of PLC. ( Programmable Logic Control )
• Install Input/Out put Component and Pheriperial PLC.
• Arrange Input/Output Assignment.
• Arrange Ladder Diagram Control
• Arrange Mnemonic ( Programme Logic )
• Programming Control and Editing by PLC. Progrmme Console
• Trouble Shooting

5. Curricullum and Syllabus ( 35 Hrs )
a. Installing Pheriferial PLC
• Installing PLC. Configuration
• Installing I/O Component ( Push Button Switch,
Relay/Contactor and Pilot Lamp )
• Trouble Shoooting
b. PLC. Operation
• Conversion Convensional Wiring to Ladder Diagram
• Arrange Ladder Diagram Application (CX-ONE programme)
• Arrange Mnemonic ( PLC. Logic Programme )
• Programming several Wiring Diagram Control Motor to PLC. ( D.O.L; D.O.L 2 place; F & R; R & R 2 Place; Star Delta Manual and Automatic )
• Trouble Shooting

6. Facilities
a. Hand Out
b. Certificate by : MSI. TRAINING CONSULTANT
c. Hand Tools and Material for Practice – Hand Tools : – Screw Driver ( + and -)
Linemans Plier; Lon Nouse Plier;Diagonal Plier; Wire Stripping; Multy Meter; Clip On Meter; Megger.
Material : – Contactor Magnet; – Over Load Relay; – Push Button Switch; 3 phase MCB; – Single Phase MCB; Pilot Lamp; – 3 phase Electric Motor (Small < 1 KW); – Cable Terminal; -Cable NYAF 1,5 mm2; NYMHY Cable 4 x 2,5 mm2.; Timer for Star and Delta Starter Motor.; Recepticle 3 phase.; PLC. Trainer; Software Application Programme – Audio Visual Aids : LCD; Screen; Class Room; White Board.

 

3. AC. AND REFRIGERATOR MAINTENANCE
     TRAINING PROGRAMME
1. Name of Training : AC AND REFRIGERATOR MAINTENANCE
2. Duration : 5 Days ( @ 7 hrs )
3. Cost : Cost of Course : Rp. 5.500.000,-/Candidat ( In Hause )
Rp. 5.500.000,-/Candidat(Institutional )

4. Goal :
After finished this Training Candidat should be able to :
• Explain Basic of AC and Refrigerator
• Introduse AC and Refrigerator Componen
• Reading and Installing Control Syastem of AC and Refrigerator
• Air Handling Heating and Ventilating AC and Refrigerator
• Trouble Shooting

5. Currikullum :
• 1. Basic Refrigeration And Air Condition
• 2. Refrigeration And Air Conditioning Component
• 3. Control System
• 4. Air Handling System
• 5. Trouble Shooting

6. Syllabus :
• 1. Basic Refrigeration And Air Condition
– Basic of Circulation ofRefrigerant
– Basic Electricity Control
• 2. Refrigeration And Air Conditioning Component
– Kind Of Refr. And AC Component( Compressor;Blower;Condensor; Evaporator; Thermostat; Over Load Relay; Capasitor; Heater; Filter etc. )
• 3. Control System
– Reading and Installing of Wiring Diagram Control
• 4. Air Handling System
– Calculate Capacity of Machine for Air Handling
• 5. Trouble Shooting
– Trouble shooting for Refrigerant circulation
– Trouble Shooting for Control Syste

7. Facilities
a. Hand Out b. Certificate by : MSI. TRAINING CONSULTANT c. Hand Tools and Material for Practice
– Hand Tools : – Screw Driver ( + and – ); – Linemans Plier; Lon Nouse Plier;Diagonal Plier; Wire Stripping; Multy Meter; Clip On Meter; Megger
– Material : – Contactor Magnet; – Over Load Relay; – Push Button Switch; 3 phase MCB; – Single Phase MCB; Pilot Lamp; – 3 phase Electric Motor (Small < 1 KW); – Cable Terminal; -Cable NYAF 1,5 mm2; NYMHY Cable 4 x 2,5 mm2.; Timer for Star and Delta Starter Motor.; Recepticle 3 phase.; AC and Refrigerator Trainer
– Audio Visual Aids : LCD; Screen; Class Room; White Board.

 

4. REWINDING ELECTRO MOTOR TRAINING PROGRAMME

  1. Name of Training : “ REWINDING ELECTRO MOTOR”
    1. Duration        :  5 Days ( @ 5 hrs )
    2. Cost                  : a.  Rp. 5.500.000,-/Candidat  ( Institutional )                                                                                            b.  Rp. 7,500.000,-/Candidate ( In Hause ) min. 5 Participant
  1. Goal  :

After finished this Training Candidat should be able to :

  1. Explain about Basic 3 phase Electro Motor
  2. Use Knowledge of Rewinding Stator Electro Motor
  3. Inspection Electro Motor
  4. Remove and Install part of Electro Motor
  5. Rewinding Stator Electro Motor
  6. Testing Electro Motor
  7. Curriculum : :

5.1. Knowledge base 3 phase induction motor

  1. 2. Theory Rewinding Stator 3 phase induction motor
  2. 3. Inspect Installation 3 phase induction motor
  3. 4. Disassemble and reassemble the parts 3 phase induction motor
  4. 5. The stator coil Merewinding 3 phase induction motor
  5. 6. Operate 3 phase induction motor
  1. Syllabus
  • Knowledge base 3 phase induction motor

1.1 The working principle of  3 phase induction motor

1.2 Number of Revolution of 3 phase induction motor stator

1.3 Stars and Delta Connection Coil of 3 phase induction motor

1.4 Reversing Revolution 3 phase induction motor

1.5 Name Plate Reading of 3 phase induction motor

 

  • Rewinding Coil Stator Theory  of 3 phase induction motor

1.1 Calculation of Step coil and Rare Phase

1.2 Landscape Drawing 3 phase induction motor coil

1.3 Riwinding Coil Stator 3 phase induction motor

  • Inspecting Installation 3 phase induction motor

3.1 Measuring Prisoners Coils

3.2 Measuring Insulation Resistance Coil

3.3 Reading of Name Plate 3 phase induction motor

6.4  Dismantling parts 3 phase induction motor

4.1 Dismantling Cover Motor

4.2 Removing the Rotor

4.3 Removing the coil burned

4.4 Cleaning the Motor Stator

4.5 Replacing Rotor Motor

4.6 Replacing Motor Cover and tighten

4.7 Test the rotor rotation by hand

  • Insulation Test of Electro Motor

6.5  Rewinding Coil stator of 3 phase induction motor

5.1 Make Mal Coils

5.2 Measuring the height of the head coil

5.3 Calculating the Total Wire each Flow

5.4 Measuring Diameter Wire

5.5 Considering the heavy wire burned Emal

5.6 Setting the appropriate Wire Email

5.7 Rolled Coils

5.8 Incorporating coils and tied

5.9 Test polarity

5:10 Isolating coil

6.6 Operating the 3 phase induction motor

6.1 Connecting Motor with true-source voltage

6.2 Running the motor at the load Empty

6.3 Measuring current of Empty load

 

Jakarta, 13th of Juni 2019
LPK. MSI TRAINING CONSULTANT

Drs. Hasan Basri,CH,CHt.
Principal/Instructor